Gasboy 1000 Series FMS Startup Manual Manual de usuario Pagina 10
- Pagina / 57
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
03/07/03 2-1
Section 2
SITE INFORMATION
Before you can use the Series 1000, you must load in certain operating information. This section
provides a template for you to fill in the information needed to perform the start-up commands in
Section 11. Do not perform the commands at this time. Confirm with the customer the information
that he will be using (e.g., fuel authorizations, limitations, etc.). Successful start-up requires
coordination between separate components of the system: installation, card or key encoding, and
operation. Each item listed contains a manual reference where you can find additional
information.
For mag and optical card and FleetKey systems, the system identification, product authorization
and product limitation codes are encoded on the access cards or keys and then entered into the
system via commands. The commands you enter must match what is encoded on the cards. The
Series 1000 Card Encoding Manual and the FleetKey Operation Manual explain the encoding of
these items.
For cardless systems, the authorization and limitation codes are stored in the vehicle record. The
commands you enter must match what is stored in the vehicle record. See Fueling Restriction
Commands in the Series 1000 Cardless Operation Manual for more information.
1. COMMUNICATION PORT SETTINGS (Reference: Operation Manual: Communicating
with the Series 1000)
Port 1 RS-232/RS-422 ______ Baud rate ______
Port 2 RS-232/RS-422 ______ Baud rate ______
Aux. Port 1 RS-232/RS-422 ______ Baud rate ______
Aux. Port 2 RS-232 ______ Baud rate ______
NOTE: If you have a tank monitoring system, receipt printer, or Fuel Point Reader (FPR),
you also have the auxiliary communications port PCB. Port 1 is configurable for
RS-232 or RS-422; Port 2 is RS-232 only. If the system does not have a FPR,
Port 1 is always used for a tank monitor; port 2 is for the receipt printer. If a FPR
is used, it is always Port 1, RS-422, 1200 Baud; port 2 can be used for a tank
monitor or receipt printer. In all cases, the receipt printer must be set for 9600
baud.
2. SIGN ON PASSWORD (Reference: Operation Manual: LS Command)
Password (up to 10 characters)________________
3. SYSTEM CONFIGURATION (Reference: Operation Manual: SC Command)
Site Number: _________ (0000-9999)
Idle Message: ____________________ (20 characters maximum)
Number of pumps: ____ (1-8) Number of tanks: ____ (1-8)
Receipt Printer?: ____
- GASBOY INTERNATIONAL LLC 1
- CONTENTS 4
- Section 1 6
- START-UP OVERVIEW 7
- WHAT YOU NEED FOR TESTING 7
- USING THIS BOOK 8
- SITE INFORMATION 10
- BEGIN START-UP FORM 16
- SYSTEM LAYOUT 18
- JUMPER AND SWITCH SETTINGS 20
- Jumper and Switch Settings 22
- 03/07/03 5-3 22
- 03/07/03 5-5 24
- LINK MC5 TERMINAL SETUP 28
- OKIDATA 184 SETUP 30
- PUMP/DISPENSER MANUAL TEST 32
- SYSTEM POWER 34
- DC POWER 36
- GASBOY FUEL POINT READER 37
- COMMUNICATIONS TESTS 38
- Section 10 42
- START-UP COMMANDS 44
- CARD OR CARDLESS SYSTEM 45
- Start-Up Commands 46
- 03/07/03 11-3 46
- CUSTOMER TRAINING 52
- FINISH START-UP 54
- WARRANTY 55
- 55F-065 Rev. 7105 56
- Include wiring distances): 57
Relacionado con productos y manuales para Hardware Gasboy 1000 Series FMS Startup Manual
(63 paginas)
Hardware Gasboy MCE300 Manual de usuario
(71 paginas)
(71 paginas)
Hardware Gasboy 4-Hose PCU Manual de usuario
(2 paginas)
(2 paginas)
Tweco 102 Cutmaster manuels
Manuels d'utilisation et guides de l'utilisateur pour Équipement Tweco 102 Cutmaster.
Nous fournissons des manuels en pdf 2 Tweco 102 Cutmaster à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales