Gasboy MCE300 Manual de usuario

MCE 300 AND MCE 300 HE MOTORIZED PROGRAMMABLE MAG CARD ENCODER OPERATING INSTRUCTIONS C01923 GASBOY INTERNATIONAL LLC

03/07/03 2-1 Section 2 INSTALLATION ENVIRONMENTAL REQUIREMENTS The MCE 300 should be located in a clean office-type environment to insure maxi

GASBOY MCE 300 2-2 03/07/03 COMMUNICATION CONNECTIONS The MCE 300 requires the use of a data terminal for operation. The type of data terminal us

03/07/03 3-1 Section 3 COMMUNICATING WITH THE MCE 300 COMMUNICATION PORTS The GASBOY MCE 300 has two asynchronous communication ports for conn

GASBOY MCE 300 3-2 03/07/03 • Label Printer - This is an optional printer used to print information onto self-adhesive labels. This device would

Communicating with the MCE 300 03/07/03 3-3 SIGN ON To guard against unauthorized use of your MCE 300, a security access code is required before y

GASBOY MCE 300 3-4 03/07/03 W - CHANGE SECURITY ACCESS CODE Once you have gained access to the MCE 300 and wish to change the preset access code,

Communicating with the MCE 300 03/07/03 3-5 E - EXIT COMMAND MODE If you are currently in the command mode, by entering the E command the system e

03/07/03 4-1 Section 4 MCE 300 COMMANDS COMMAND STRUCTURE Once you are in the command mode, you can enter various one letter commands to load,

GASBOY MCE 300 4-2 03/07/03 H - PRINT HELP LIST This is a list for quick reference of the available system commands. To print the help list: At

GASBOY MCE 300 and MCE 300HE MOTORIZED PROGRAMMABLE MAG CARD ENCODER OPERATING INSTRUCTIONS C01923 Rev. 03/07/03 GA

Commands 03/07/03 4-3 T - PRINT CARD TOTALS This command is used to monitor operation of the MCE 300. There are three totals maintained. They ar

03/07/03 5-1 Section 5 CONFIGURATION OVERVIEW The MCE 300 can be customized to your specifications through switch settings and the L (Load Conf

GASBOY MCE 300 5-2 03/07/03 SOFTWARE CONFIGURATION The following sections describe the various configurable features available with the L command.

Configuration 03/07/03 5-3 PIN LAYOUT Your MCE 300 can calculate and print PINs (Personal Identification Numbers) used on GASBOY CFN and Series 10

GASBOY MCE 300 5-4 03/07/03 LABEL LAYOUT The MCE 300, when used with an optional tractor feed printer, can print information onto self-adhesive la

Configuration 03/07/03 5-5 RESET CARD DATA FILE The opportunity to reset the card data file is provided at the end of the L (Load Configuration) c

GASBOY MCE 300 5-6 03/07/03 L - LOAD CONFIGURATION This command is used to configure the MCE 300 software to your specifications. The configurati

Configuration 03/07/03 5-7 Example: Card Layouts The following two layouts are examples of typical Series 1000 and CFN card layouts. The single

GASBOY MCE 300 5-8 03/07/03 To load the configuration: 1. At the * prompt, type L. The system displays: ENTER NO. OF CHARACTERS ON CARD (DATA

Copyright 2003 by Gasboy International LLC All rights reserved. The information in this document is confidential and proprietar

Configuration 03/07/03 5-9 Example: Configuration Load

GASBOY MCE 300 5-10 03/07/03 L COMMAND MESSAGES CONFIGURATION COMPLETE The configuration was completely loaded. CONFIGURATION NOT COMPLETE!

Configuration 03/07/03 5-11 C - PRINT CONFIGURATION This command is used to view the present configuration. In cases where an optional printer is

GASBOY MCE 300 5-12 03/07/03 C COMMAND MESSAGES CARD FILE HAS DATA There is data loaded in the card file. NO DATA IN CARD FILE There is no d

03/07/03 6-1 Section 6 CARD DATA FILE OVERVIEW The card data file is used for storage of the actual card data that will be used for encoding c

GASBOY MCE 300 6-2 03/07/03 D - LOAD CARD DATA FILE This command is used to input the actual card data into the card data file. The option to res

Card Data File 03/07/03 6-3 CTRL C (control C) Indicates that no more cards need to be loaded into the card data file and that the D command shou

GASBOY MCE 300 6-4 03/07/03 D COMMAND MESSAGES CARD FILE IS FULL! The card file is full and will not accept any more entries. The card file mu

Card Data File 03/07/03 6-5 P - PRINT CARD DATA FILE This command is used to print contents of the card data file. The printout will be formatted

GASBOY MCE 300 6-6 03/07/03 P COMMAND MESSAGES CARD DATA ERROR! - RELOAD UNIT The data in the card data file does not match the unit's con

FCC INFORMATION Both the US Federal Communications Commission (FCC) and the Canadian Department of Communication (DOC) require specific information b

03/07/03 7-1 Section 7 ENCODE CARD DATA OVERVIEW The MCE 300 is capable of encoding data on ABA Track 2 of Mag Stripe Cards. There are two me

GASBOY MCE 300 7-2 03/07/03 S - ENCODE CARD DATA - CONFIGURATION MODE This command is used to encode the previously loaded card data onto the card

Encode Card Data 03/07/03 7-3 To encode cards (automatic mode): 1. At the * prompt, type S. The unit prompts: AUTOMATIC MODE (Y/N)? 2. Type Y

GASBOY MCE 300 7-4 03/07/03 To encode cards (non-automatic mode): 1. At the * prompt, type S. The unit prompts: AUTOMATIC MODE (Y/N)? 2. Type

Encode Card Data 03/07/03 7-5 S COMMAND MESSAGES CARD DATA ERROR! - RELOAD UNIT The data in the card data file does not match the unit's c

GASBOY MCE 300 7-6 03/07/03 M - ENCODE CARD DATA - RAW MODE This command is used to encode card data that is loaded through the keyboard. Any siz

Encode Card Data 03/07/03 7-7 To encode cards in raw data mode: 1. At the * prompt, type M. The unit prompts: ENTER DATA: 2. Type the data to

03/07/03 8-1 Section 8 READ CARD DATA OVERVIEW The MCE 300 is capable of reading card data from ABA Track 2 of Mag Stripe Cards. There are tw

GASBOY MCE 300 8-2 03/07/03 R - READ CARD DATA - CONFIGURATION MODE This command is used to read data previously encoded onto cards. In cases whe

Read Card Data 03/07/03 8-3 N - READ CARD DATA - RAW MODE This command is used to read data previously encoded into cards while ignoring the prese

03/07/03 9-1 Section 9 LABELS OVERVIEW The MCE 300, when used with an optional tractor feed printer, can print information onto self-adhesive

GASBOY MCE 300 9-2 03/07/03 B - PRINT LABELS This command is used to print labels for card data previously loaded into the card data file. LABELS

Labels 03/07/03 9-3 Example: Example: Labels Printed: Labels should be attached to the card as shown in the drawing below. Labels attached in t

GASBOY MCE 300 9-4 03/07/03 B COMMAND MESSAGES LABEL NOT FORMATTED - The configuration is not loaded to allow the printing of labels. The B comma

03/07/03 10-1 Section 10 PREVENTIVE MAINTENANCE The magnetic heads of the MCE 300 reader should be cleaned every 1000 passes or 6 months, whic

03/07/03 11-1 Section 11 DIAGNOSTICS PURPOSE The MCE 300 is designed to allow access to 3 diagnostic tests. These tests provide information wh

GASBOY MCE 300 11-2 03/07/03 TEST 2 - ROM TEST This test reads each location in the program chip, calculates a checksum and compares it to a check

03/07/03 Contents-1 CONTENTS FCC APPROVAL i Section 1: INTRODUCTION Purpose...

Diagnostics 03/07/03 11-3 TEST 3 - DIP SWITCH TEST This test reads the setting of the DIP switches and displays their present status. A 1 indicat

03/07/03 12-1 Section 11 SPECIFICATIONS CHARACTERISTICS Dimensions: MCE 300 13" L x 11" W x 3 5/8" H MCE 300HE 15 1/4

GASBOY MCE 300 12-2 03/07/03 PC BOARD LAYOUT

03/07/03 13-1 Section 13 PARTS USING THE PARTS LISTS The following pages list parts information for the MCE 300 Mag Card Encoder Models. Usi

GASBOY MCE 300 13-2 03/07/03

Parts 03/07/03 13-3 C05911 MCE 300 Item Part No. Description 1 C09053 Power Supply 2 C05904 Cable Assy., AC Power 3 C04371 Trim Material, Ed

GASBOY MCE 300 13-4 03/07/03

Parts 03/07/03 13-5 C06187 MCE 300HE Item Part No. Description 1 C07398 Cable Assy., AC Power 2 C08330 Filter, RF Module 3 C08723 Fuse, 2

GASBOY MCE 300 13-6 03/07/03

GASBOY MCE 300 Contents-2 03/07/03 P - Print Card Data File ... 6-5

Parts 03/07/03 13-7 C05902 MCE 300 PCB ASSEMBLY Item Part No. Description 1 C05902 PCB Assy. 2 C03315 Connector, Jumper 2-Pos Fe 3 C02824 3

GW01 - 6/04/02 Rev. 1 WARRANTY General Statements: Gasboy International LLC. warrants all new equipment manufactured by Gasboy against defective ma

03/07/03 1-1 Section 1 INTRODUCTION PURPOSE This manual has been created to help familiarize you with your GASBOY MCE 300 and MCE 300HE Magnet