Gasboy CFN Series Site Controller III Start-up Manual de usuario Pagina 15
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MDE-4793A CFN Series Site Controller III Start-up Manual for CFN III Versions 3.5 and above · November 2008 Page 9
Important Safety Information
Hazards and Actions
WARNING
Spilled fuels, accidents involving pumps/dispensers, or uncontrolled fuel flow create a
serious hazard.
Fire or explosion may result, causing serious injury or death.
Follow established emergency procedures.
!
Collision of a Vehicle with Unit Fire at Island Fuel Spill
The following actions are recommended regarding these hazards:
• Do not go near a fuel spill or allow anyone else in the area.
• Use station EMERGENCY CUTOFF immediately. Turn off all system circuit breakers to the island(s).
• Do not use console E-STOP, ALL STOP and PUMP STOP to shut off power. These keys do not
remove AC power and do not always stop product flow.
• Take precautions to avoid igniting fuel. Do not allow starting of vehicles in the area. Do not allow open
flames, smoking or power tools in the area.
• Do not expose yourself to hazardous conditions such as fire, spilled fuel or exposed wiring.
• Call emergency numbers.
- Site Controller III Start-up 1
- Approvals 2
- Trademarks 2
- Table of Contents 3
- 7 – System Power 53 4
- 11 – Communication Tests 69 5
- 13 – Start-up Commands 79 5
- 14 – Customer Training 101 6
- 15 – Finish Start-up 105 6
- Introduction 7
- Related Documents 7
- Based on Site Configuration 8
- Abbreviations and Acronyms 9
- Start-up Overview 10
- Required Tools 10
- Filling Out the Start-up Form 11
- Using This Manual 11
- Warranty 12
- In an Emergency 14
- Hazards and Actions 15
- Important Safety Information 16
- 3 – Site Information 17
- Authorize Users 18
- Receipt Messages 19
- Broadcast Messages 20
- Load Product - Fuels 20
- Load Fuel Inventory 21
- Load Tank 21
- Load Prices 22
- Load Fuel 22
- Load Pumps 23
- Load Cutoff 23
- Load Tax 24
- Lockout Type 24
- CRON Commands 25
- Load Remote Host Phone Number 25
- Load Merchandise Prods/Depts 26
- Load Merchandise Inventory 27
- Load Price Lookup 27
- Profit Point Product Layout 28
- Profit Point Default Keyboard 33
- 4 – Begin Start-up Form 35
- 5 – Physical System Layout 39
- ICR Assembly 40
- Fuel Point Components 42
- Electronic Pumps 42
- SC COMM CPU PCB 43
- Switches, S1 and S2 44
- SC Memory I/O Board 45
- Switch S2 46
- Pump Control EXPMUX CPU Board 47
- Figure 6-4: EXPMUX CPU Board 48
- Pump Control I/O PCB 51
- DIP Switches 53
- CPU PCB Jumper Settings 54
- RS-232/RS-485 Converter 55
- POS Distribution Box (D-Box) 55
- Switch SW1 56
- Pumps and Dispensers 57
- Standalone Star Printer 57
- 7 – System Power 59
- System Power 60
- Verify General Guidelines 61
- Manual Override Test 61
- Turning On AC Power 63
- Configuring the PPC 64
- Software Configuration 65
- Hardware Configuration 65
- Keyboard Configuration 65
- Set Up CONFIG.POS File 65
- Printer/Logger 66
- Remote Terminal Setup 67
- SC Configuration Changes 67
- +5 VDC Measurement 69
- +5 VDC Adjustment 71
- +12 VDC Measurement 72
- 11 – Communication Tests 75
- SC III or Remote Terminal 76
- Tank Monitor (Serial Port) 77
- Test (Optional) 80
- Before Using Fuel Point 81
- Reader Entries and Fuel Point 83
- 13 – Start-up Commands 85
- Sign-on and Preliminary Steps 86
- Security Key Management 88
- Card Lockout 94
- Load Authorization 95
- Load Limitation 95
- Load Cron 96
- Load Phone 96
- Enable Devices 98
- Cash Drawer, Shifts 99
- Optional Features 100
- Reset Transaction File 101
- Diagnostics and History 102
- Verification and Backup 103
- Site Data 103
- Standalone Profit Point Setup 104
- SC III/POS WS Setup 105
- 14 – Customer Training 107
- Customer Training 108
- 15 – Finish Start-up 111
- IMPORTANT INFORMATION 112
- Sample Form 113
- Sample FormSample Form 114
- CFN System Start-up Form 119
- 1. SITE IDENTIFICATION 119
- 3. SYSTEM DESCRIPTION 120
- 4. COMMUNICATIONS 120
- 5. BREAKER NUMBERS 121
- 6. SYSTEM ENVIRONMENT 121
- 7. CONDUIT 121
- 8. SYSTEM POWER 121
- 9. DC POWER 122
- 10. SYSTEM APPROVALS 122
- 11. CUSTOMER KNOWLEDGE 122
- 12. ATTACH PRINTOUTS 122
- 13. PARTS USED 122
- (include wiring distances) 123
Relacionado con productos y manuales para Hardware Gasboy CFN Series Site Controller III Start-up
Hardware Gasboy C01533 Manual de usuario
(2 paginas)
(2 paginas)
Hardware Gasboy Fuel Point Manual de usuario
(24 paginas)
(24 paginas)
Hardware Gasboy 2020 Manual de usuario
(1 paginas)
(1 paginas)
Hardware Gasboy VT 520 Manual de usuario
(16 paginas)
(16 paginas)
Hardware Gasboy 4860 Series Meter Manual de usuario
(13 paginas)
(13 paginas)
Hardware Gasboy 72S Manual de usuario
(35 paginas)
(35 paginas)
Hardware Gasboy 9820 Manual de usuario
(1 paginas)
(1 paginas)
Hardware Gasboy CFN Islander Manual de usuario
(52 paginas)
(52 paginas)
Hardware Gasboy 25 Series Manual de usuario
(7 paginas)
(7 paginas)
Hardware Gasboy 580 Manual de usuario
(44 paginas)
(44 paginas)
Hardware Gasboy 25 Manual de usuario
(7 paginas)
(7 paginas)
Hardware Gasboy 032867 Manual de usuario
(8 paginas)
(8 paginas)
Hardware Gasboy 70 Series Manual de usuario
(53 paginas)
(53 paginas)
Hardware Gasboy 580 Series Manual de usuario
(50 paginas)
(50 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.176 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales